Opening the book…
There are many grafting techniques used in horticulture. There use varies with the purpose of the grafting. The most common types of grafting are described in this section.
Bud grafting: Both T-budding and Chip-budding are grafting techniques that involve taking a single bud from the desired scion plant and inserting it into the side of the selected rootstock. In T-budding (Figure 9-37), a T-shaped cut is made in the bark of the rootstock and the bud slid just under the bark so the cambial tissues touch. Some grafters prefer to invert the T to prevent the potential of water becoming trapped behind the bark. The bud is then wrapped and sealed to encourage it to unite with the rootstock. As the bud grows, it will form the desired stem and variety of the scion plant. Bud grafting allows propagation of new plants using very limited amounts of scion material onto easily germinated rootstock. It is commonly used for woody plants like roses and fruit trees.
Cleft grafting: Cleft grafting is often used when the rootstock is larger than the scion wood. It requires that the rootstock be split down the center to form a cleft (Figure 9-38). This is typically done by cutting the top of the rootstock at an angle and splitting it with a grafting knife. The smaller scion is cut to form a wedge shape at the bottom and then inserted into the cleft so the cambium layers of scion and stock meet. The union is wrapped tightly to encourage the scion and stock to fuse together. As the scion grows, the wrap is loosened and eventually removed. Cleft grafting provides close contact between the scion and stock so they can unite easily. This technique can be used to top-work an established tree for purposes of cultivar change or rejuvenation of older trees.
Whip grafting: For any graft to be successful, the cambium layers must match up. The cambium is the source of all future vascular tissue in the stem. For nutrients to continue to flow, the vascular tissues of the two components have to align. Whip grafting is used join scion and rootstocks of similar diameter using a slanted cut. The slant increases the contact area between the two pieces and thus increases the chance for cambial alignment. The most difficult version of a whip graft is called the whip and tongue. It creates a slanted “z” for added strength and surface area. While it is difficult to master it is the most successful of the whip styles. To create such as graft (Figure 9-39, left), first cut the rootstock and scion at complementary angles, then create the flap on the scion by notching and removing the outer bark. In the root stock, make a nearly vertical cut that match up with the flap on the scion. Once the cuts are complete, slide the scion wood into the matching notch as seen in this image. The grafted area needs to be supported and protected from desiccation. To accomplish this grafting tape – or other types of stretchy tape (electrical for example) is wrapped around the joint. When healed, the union is smooth and strong (right). Whip grafting is commonly used for grafting young rootstock and scion material that are the same diameter. It allows rapid grafting and is used for many fruit and ornamental trees.
Bridge grafting: Bridge grafting is a technique used to repair trees by grafting scion material above and below the damaged area of the trunk. The bridge grafts help transport nutrients and water past the damaged area so the tree can recover. Bridge grafting can restore growth to a tree section that would likely have died from significant damage without grafting.
In Figure 9-40, the diagram on left shows an example of how this works. A young tree was girdled by mice. Item B shows that tree’s trunk after the wound has be cleaned and the bark along the margin of wound trimmed back to healthy wood. Item C show the scion wood with tapered end ready for insertion. Item D shows a cut-away, with scions inserted beneath the health bark (“w” mark insertion point). Item E show the multiple scions in place and ready for waxing. The wax seals pathogens and water that might lead to rot. The scions act like hoses to allow the flow of water from the roots to the shoots and the flow of nutrients in both directions. The scions, as living wood, grow with the tree and eventually their bark merges with that of the original tree (Figure 9-40, right).
This page titled 9.3.2: Methods of Grafting was last modified on Sat, 14 Nov 2026 17:26:51 GMT and is shared under a CC BY-NC-SA 4.0 license and was authored, remixed, and/or curated by Stephanie Harvey.
The book could not be loaded just now.